Jump to content

cimmer

Supporting Member
 View Profile  See their activity

  • Posts

    961

  • Joined

  • Last visited

  • Days Won

    5

 Content Type 

Everything posted by cimmer

  1. cimmer
    I replaced mine last year on my bike. You might want to have a new gasket for the middle gear case also in case yours is broken and unusable. Just take your time getting the clutch activator out of it space. It will come out but you will have to work at it. I also took the time to rebuild the clutch master cylinder at the same time and it made a world of difference on the action of the clutch. I am planning on rebuilding the brake system this year and replace all the hoses with Rick's steel braided set for the 89 Venture. Right now I have a front caliper that is seeping a bit. I also replace the brake fluid with synthetic brake fluid so moisture wouldn't be an issue down the road. Good luck and just take you time is the key and also what the others said about the piston seal and such. Rick F.
  2. cimmer
    Wish I could make it but I am headed out of town again for work myself. I dont think I will be back in time for Sat breakfast either Owl. I dont expect to be back till late on Friday night. Maybe next time.. Rick F.
  3. cimmer
    Welcome Dave, With your idle problem, you might want to check for air leaks around the carbs and double check the plugs on the sync tubes as they will crack and are hard to see unless you move them a bit. I had this on my 89 Venture that had been sitting in a garage for 5 years before I purchased it. On bleeding your brakes, be aware there is a bleeder between the front of the tank cover and the steering head. I had missed this one when I first bleed mine and it makes a difference. Also the left front and the rear brake is link together. I would suggest if you havent yet, download the service manual from the site here and it will help you alot with the maintenance on your ride. Enjoy the bike, I know I sure enjoy mine. Rick F.
  4. cimmer
    You might want to check and see if the cables need some oiling. The RPMs should drop off fairly quickly. I have had an issue like this and only needed to oil the cables and that loosened them up. You can check this with the left engine side cover off and watch the throttle shaft as you open and release the throttle. They should snap back quickly. Hope this helps. Rick F.
  5. cimmer
    Was searching for Yamaha Ventures and the site came up and I have been here ever since. Rick F.
  6. cimmer
    Download the service manual file for your 1st gen bike from this link here.. http://www.venturerider.org/forum/showthread.php?t=3384 It talks about how to remove the fairing and just reverse the order to reinstall it. Also just ask questions here. Start with the inner panels and the then the outer sides. Good luck and let us know how it is going.. Rick F.
  7. cimmer
    If you want to do it yourself, try some of the following places: http://www.flatoutmotorcycles.com http://www.buckeyeperformance.com here you might need to email or call them to see about cost. There are other places online to get parts also, just find one you like. A lot of the places have the yamaha parts fiches online so you can see the parts and click on what you want to order. I hope this helps you out. Rick F.
  8. cimmer
    I think you need to ask yourself if you want to be around all these people for 5 nights. Staying at a college in the summer in the dorms can be inexpensive and the bull sessions at night could be fun and entertaining.They might be sharing photos from past trips or who knows what. It doesn't sound unreasonable for 5 night and 4 1/2 days worth of food to me. I guess it just depends on what you expect from the trip. Good Luck, Rick F.
  9. cimmer
    Does anyone know what the enclosed packet is with the seal kit? I have one of the rear caliper seal kits already but haven't opened it yet but was wonder what the packet is used for. The service manual doesn't mention anything about it so that is why I am asking. I am thinking maybe a lubricate for the seals but I was just planning on using brake fluid to do that when I assembled them. Thanks, Rick F.
  10. cimmer
    I am looking to rebuild my braking system on my Venture and have a question on the caliper seals for the front brakes. The microfiche shows two different calipers seal kits for the front calipers. Part numbers 1KT-W0047-00-00 and 1NL-W0047-00-00. I did notice there is also two different part numbers for the piston so I am guessing that the pistons are different sizes and that is why there are two different seal kits. Is this correct? Thanks Rick Fink
  11. cimmer
    Or maybe Polaris isnt sponsoring Petty Enterprises anymore and therefore Kyle can ride anything he wants to now. I know that a few years ago Richard Petty was doing commericals for Polaris and I noticed that he hasnt for a while. Just a thought. Rick F.
  12. cimmer

    Can-am spyder

    cimmer replied to jonesy's topic in Watering Hole

    looks like Jay Leno got the very first production one. He has a video of it on his website. http://www.jaylenosgarage.com/ Rick F.
  13. cimmer
    One thing you need to take into consideration is where is the TV going to be places. Plasma is a good choice if their is no reflections of light. LCD is better if there will be outside light, ie sunshine, on the screen. I would recommend a 1080p HDTV with an upconvertor built into the unit. This will help upgrade the incoming signal to 1080p standards and helps with old DVD movies and such. I just purchased a Sony 40" LCD Bravia at a local electronics store. They were more then happy to let me see different video sources on different TVs. I went with a LCD as it is sitting in my living room with a big picture window facing west. I did break down and get a HD cable convertor and and HD package from the local cable company. I used a HDMI cable to connect between the two. Now some channels are broadcast in 720i, 720p and 1080i but there is still alot of programs that are still standard format. I suggest go to a local shop and talked to them about what you want and expect and see what they recommend. Good Luck.. Rick F.
  14. cimmer
    Check out this link .. http://www.taxadmin.org/FTA/rate/sales.html There are still some states with no sales taxes yet. So I would guess those would be the best states to get anything in. Rick F.
  15. cimmer
    check this out in the tech library http://www.venturerider.org/forum/showthread.php?t=6875 I think that will answer your question. Rick F.
  16. cimmer
    I am glad someone here was able to get it. I see there is a used one going for $102 plus shipping also but the bidding is open on that one still. Rick
  17. cimmer
    There is a Venture line travel trunk rack on ebay for a buy it now price of $70 plus $11.50 shipping if anyone is interested. http://cgi.ebay.com/ebaymotors/YAMAHA-VENTURE-TOURBOX-RACK-NEW_W0QQcmdZViewItemQQcategoryZ35580QQihZ002QQitemZ120168798180QQrdZ1QQsspagenameZWDVW Rick F.
  18. cimmer
    Thanks all, I was looking at the Custom Dynamics Radiantz 1.85 " 1157 direct base leds but was wondering on the clearance issues but it sounds like they will work. I am wondering if installing a load resistor wouldn't solve the warning light issue as I am sure the computer is looking at the load to see if all of the bulbs are working or not. I think I have seen some listed for this purpose. Thanks again.. Rick F.
  19. cimmer
    Has anyone installed LEDs in the 1st gen in place of the 1157 bulbs and if so, what did you use and how do you like it. I found that I have a burnt out running light in my taillight and was thinking about using an LED bulb for them. Thanks, Rick F.
  20. cimmer
    I found this price for a 89 VR on Flatout today. 9 DIAPHRAGM ASSY 1FK-14940-09-00 (replaces 1FK-14940-00-00) 1 $63.02 Checked on other years and found the same price for them also. Rick F..
  21. cimmer
    Thanks for the information as I plan on doing the progressive swap out this winter on my 89VR. I would prefer it to be a nice riding good cornering upgrade then too harsh. I am sure I will use your information and get it right. Thanks again. Rick F.
  22. cimmer
    Dont forget to grease the driveshaft spines also at this time. When I had my 89 VR swing arm out, I found the shaft was dry also. It isnt hard to do and I think there is some information on doing all of this in the tech library. Good Luck.. Rick F.
  23. cimmer
    I use Flatout Motorcycles http://www.flatoutmotorcycles.com/default.asp They are also easy to deal with and order from. Rick F.
  24. cimmer
    I have an 89 VR with the superbrace on it. It was a tight fit with out any boots as my bike didnt come with them as the 90's did. If you pull up the boot how do the holes line up. I would be tempted to pull the boots up and then attach the brace and then see if you can get the boots back into their proper place. Check and see what might need to be clearanced to make them fit properly. Good luck and let us know how it goes. Rick F.
  25. cimmer
    From what I have found looking for rear brake rotors. The 86-93 Venture was the only yamaha to use this type of rotor and they arent cheap at all, even from Flatout. But EBC does make a replacement rotor for the Venture and I have seen it new for around $170 at MAWonline.com. Some do show up on Ebay from time to time. But you never know if you are getting a good one or a questionable one. Good Luck and enjoy the bike. Rick F...
×
×
  • Create New...