Jump to content

flb_78

Expired Membership
 View Profile  See their activity

  • Posts

    2,702

  • Joined

  • Last visited

 Content Type 

Everything posted by flb_78

  1. flb_78
    I support animal husbandry.
  2. flb_78

    Oil

    flb_78 replied to Little Bob's topic in Watering Hole

    Rotella T6 is available in 5w40 Rotella T is available in 15w40 and is not a synthetic oil.
  3. flb_78
    I just put them together today and slapped them in the trees. Tomorrow I'll bolt all the tupperware back on and figure out where the wires aren't supposed to go.
  4. flb_78
    Loctite 38657 High Flex Gasket Maker. This is some good stuff. Install your o-rings and then put a thin bead of this around the o-ring.l http://www.jbtoolsales.com/media/ecom/prodlg/LCT-38657.jpg
  5. flb_78
    Mr. Myers came to my rescue by fabbing up a seal driver for 43mm forks. This driver will be passed around to other members who want to work on 2nd gen forks. 1 side drives in the bushing and seal, the other side drives in the dust seal. Ruffy is first on the list. *edited for mor guder picshures.
  6. flb_78
    I wasn't aware that this particular fastener was threaded into rubber.
  7. flb_78
    You need an impact driver set. http://www.sears.com/shc/s/p_10153_12605_00999001000P?sid=IDx20070921x00003a&ci_src=14110944&ci_sku=00999001000P http://s.shld.net/is/image/Sears/00999001000?hei=248&wid=248&op_sharpen=1&resMode=sharp&op_usm=0.9,0.5,0,0
  8. flb_78
    I bet their rates are going to go up, 75% of their business is in Japan.
  9. flb_78
    My last one came from ebay.
  10. flb_78
    Sounds good.
  11. flb_78
    If your near a Harley dealer, you could probably pick up a set of take off's from a touring model. They're not any louder than stock, just a different tone. You'll have to fab up some mounting brackets for them.
  12. flb_78
    The leg measures 43.02mm diameter. The tool measures 42.09mm, 90 degrees from the cuts.
  13. flb_78
    It's a picture of the tool not quite fitting on the fork.
  14. flb_78
    OH NO!!!
  15. flb_78
    Sorry about that. I forgot to provide the reference. http://www.totalmotorcycle.com/photos/2007models/2007models-Yamaha-RoadlinerS.htm And right on Star's site. http://search.starmotorcycles.com/?all=u1&i=1&pa=star&q=ceramic&u1=q
  16. flb_78
    I don't know about Kawasaki, but Yamaha puts a nikasil or ceramic coating on the cylinders. I have a set of jugs off a Roadstar with 40,000+ miles on it and there is no ring ridge and the cross hatching is still visible.
  17. flb_78
    I might be in Nicholasville tomorrow applying for a job. Depends on if I go to Campbellsville to check on one.
  18. flb_78
    The CB750 Nighthawk is a fine machine. The last of the UJMs.
  19. flb_78
    The seal is 54mm O.D., 42mm I.D., and 11mm thick. The fork leg is 43mm.
  20. flb_78
    I believe they are. I'll have to check.
  21. flb_78
    Ok, a little searching answered the question. If you're willing to drop down a size to a 130/90-16, I think this would work. http://www.motorcycle-superstore.com/2/29/393/14941/ITEM/Duro-HF-904-Median-Dual-Sport-Rear-Tire.aspx
  22. flb_78
    What size tire does a 1st gen run? 140/90-16?
  23. flb_78
    What did you use to drive in the bushing and seal? I can't find a PVC pipe the proper size and I'd hate to sink $40+ into a tool that I'm only going to use once.
  24. flb_78
    I ended up securing my chrome piece with velcro.
  25. flb_78
    Holy Threadnecromongering!! 3 years old!! anywho... It doesn't matter as long as the cables are going to proper radios. The CB antenna cable should go to the box mounted under the trunk.
×
×
  • Create New...