Jump to content

Rocket

Expired Membership
  • Posts

    2,485
  • Joined

  • Last visited

Everything posted by Rocket

  1. Maybe It's telling you, it's too dry & hot, not moist & cool (as per normal)...........:rotf:
  2. Use some Threebond 1104 sealant on the wires where they go through the rubber (also packaged as Yamabond). It is a semi drying sealant, used on scoots.
  3. Yup, should check in at work today, to see what I'm up to for the next few weeks. Also need to get another leave pass submitted, for PIP when I arrive there. Don't know if I will be able to get away again for PIP, but now I have a better idea of the travel time involved.
  4. I had done that as an interm fix, right after getting the deerhunter, with an right angle bracket to hold it. Remember to put in a jumper wire for your rear level sensor, otherwise it will show as low brake fluid on the CMS. Keep the level sensor from your old one, if it works ok.
  5. http://www.plastex.ca/ Look over some of the pics on the site.........
  6. Yup, I re-stocked as well + got some for others in the Wainwright area.
  7. After getting the"0", did you press ether of the larger rectangler buttons, to select front or rear, before pressing the auto / manual button or the 3 smaller square buttons????
  8. That describes the prairies in general, USA or CDN side of the border...........
  9. It's a wonder you didn't bust the camera part, with that pic of "Mother". I had suggested to Freebird, using that 350 HP outboard as a weedwacker for the pond.......
  10. Yup, Sierra is very good to deal with, but wingstuff only ships UPS & that gets costly, for us.........
  11. Or the geographical centre of North America...... As the sign I saw yesterday, at Rugby, North Dakota.......
  12. No good for a Canuck to shop there, the UPS shipping fees will double the cost. A few that bought there & got hit with brokerage & other fees.
  13. I can use the bottom middle one (013.jpg). I just saw this as I still on my way back to Alberta from the rally. Left Grandpagak's yesterday, visiting with Friesman1 today.
  14. Too bad it wasn't ready for the rally, but some progress is better than none...........
  15. You can always pass her a big hammer, to knock more off....... :duck:
  16. The line was full of air too, don't think Fred swallowed any fluid, from the plastic line we connected to the bleed nipple.
  17. Had we been talking CDN prices, he is about 4 thousand too low........ 2 thousand will get you a fixer upper (almost basket case)..........
  18. Only problem I see, is the probable lack of support, to get a scoot fixed fairly quickly, in the Jasper area. This needs to be considered in any location chosen. I was not at Ft Collins, but the support from the bike shop, near this years Rally HQ, was outstanding.......... :thumbsup:
  19. You could jump to the output side of the solinoid (witch is mounted to the left side of the battery box (be carefull not to ground out to the frame). The starter itself is attached to the upper case half, at forward portion of Cylinder #2 (left front) below the exhaust pipe.
  20. There has been no comments on the forum, but with the type of shirt you wore, you looked the wettest, even though, you both got equally drenched......
  21. Flatout is listing at $17.92 each & the rubber seals for the retention bolts are $1.65 each (16 of these total)
  22. Not at some CDN dealers they want $25. each. That is why I have been ordering at Flatout, to get away from the gouging.....
  23. Now about 20 miles away from Grandpagak's place, will hit there tomorrow. When I can look for it in daylight............
  24. I did, as I bought the one Sarges46, had for his 1st gen (in March). I need to get some stiching on the seat done, before installing it.
  25. Yup the jacket pockets are loaded as per normal... spot emergency locator, wallet, case for sunglasses, smokes & lighter, money for toll bridges, ID for border crossings (last 2 in easier acess pocket instead of digging wallet out).
×
×
  • Create New...