Jump to content

Ga Dawg

Expired Membership
 View Profile  See their activity

  • Posts

    64

  • Joined

  • Last visited

Reputation

10 Good

Personal Information

  • Name
    Scott M. Bowen

location

  • Location
    Rydal, United States

Converted

  • City
    Rydal

Converted

  • Home Country
    United States

Converted

  • Bike Year and Model
    1987 Ventura Royale

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Ga Dawg
    Where you able to conect it so your intercom and CB all work together? If so how did you do it? Thanks
  2. Ga Dawg
    Mine went out and I tightened and cleaned the battery connection and has worked fine ever since.
  3. Ga Dawg
    Thanks for the heads up Gary. Rick at Buckeye Performance has one on the way to me. Thanks Rick!!
  4. Ga Dawg
    Does anyone have or can tell me where to get a right side (clutch cover) Engine cover? I sure could use one. You can PM me if you like. Thanks!
  5. Ga Dawg
    Does anyone have a side engine clutch cover they would like to sell for a 87 VR. I sure could use one. Thanks!!
  6. Ga Dawg
    Thanks to all that have given advise. I am going to try a Barnett clutch plate from Buckeye Performance along with a new slave cyl. I will let you know what happens. Thanks!
  7. Ga Dawg
    Just changed the oil in the 87 Venture and went for a short ride of about 20 miles. I used Yamalube 4 Stroke 15-40. Got out the driveway sped up and noticed a slight clutch slip in 4th gear. By the time I got back to the house it would barely pull up the smallest hill. The dealer assured me this was the "recommended oil" from Yamaha. Any body had problems like this and these wet clutches? You would think that if it were a Yamaha product it would work. There is no engineers stamp on the back just a stamp that says MA and a circle around it. I know this has been a huge topic here on which oil to use but I figured going with brand specific oil with Yamaha's name on it would be good. What should I do? Thanks!
  8. Ga Dawg
    Thanks I will let yall (from the south) know how it goes. Thanks for the ideas!
  9. Ga Dawg
    I am going to replace fuel filter, air filter,and plugs. Also, I will check the slides to make sure they are not stuck. When they do stick what is the best way to unstick? Carb cleaner? Thanks!!
  10. Ga Dawg
    I had replaced the diaphrams recently. What would cause those slides to stick? What should I do? Thanks!
  11. Ga Dawg
    Does anyone know what would cause an '87 VR to red line in 2nd gear at 65 mph but not get above 4500rpm and 75 mph in 5th gear. It does sputter a little around 6000 rpm but will recover up to the red line. I normally don't do this to the engine but was trying to blow out the jets in the carbs after 2 cans of Sea Foam run through her this past year. It runs great but just a little slugesh in high gear. Any insight would be great and I just got carbs sync. this weekend. Is this normal? THANKS!!!
  12. Ga Dawg
    Thanks, I will check these things out! Thanks for the help!!
  13. Ga Dawg
    Just wanted to see what the Venture Nation thought about the top speed for a 87 venture would be. I have been driving mine around town and on trips not over 300 miles round trip but the other day I was on the interstate and could only get her up to 80 MPH. This is plenty fast enough and I very rarely want to exceed 70 MPH but was wondering if my slides/ Diaphragms or carbs are out of sink. What do ya'll think? The bike has about 30000 miles on her and idles, starts quick and runs fine. At high RPM there is some sputtering when in low gear and getting the tach up high. Thanks!!!
  14. Ga Dawg
    How about the trailer hitch. I need one. Please PM me. Thanks!
  15. Ga Dawg
    Yes, I also have the boards and the heal/toe shifter. Maybe I will look into the seat issue this winter. Thanks!
×
×
  • Create New...