BlueSky

Heavy duty springs probably will displace more oil and raise the level if you use the same amount as before. Safest method would be to measure from the top I would think.

Have you checked the first gen parts for sale section?

That's a nice trailer. I bought a 5' x 8' trailer from Lowes to trailer my Kawa home from WI where I bought it. When I bought the RSV, the trailer was too short. I used two sections of 2" plastic pipe that I had cut for fishing rod holders on the beach and rope to hold the tail gate back at an angle to keep it from rubbing on the trunk of the RSV.

I've been watching a lot of utube videos lately about WWII and I'm amazed at the courage and sacrifices made to beat back the Japanese and Germans. So many young men willingly went on missions that they knew there was little chance of surviving. I can only hope that I would have had that level of courage. I served a tour in the USArmy in S. Korea but did not have to fight so I don't know. My respect and eternal gratefulness for these young men has no bounds.

I guess Skid is so busy mayoring that he doesn't have any spare time.

In my opinion, a closed trailer is the best for bike trailering especially if you are going long distance. One reason I came to this opinion is that when I open trailered my Kawasaki from NC to Homestead FL to my new job location in February it rained a lot on the way and the snowbirds were driving to FL from snow country with salt all over their cars. The rain washed the salt off their cars onto the road and then it was sprayed up on my motorcycle. The bike was lightly covered with salt and I was so busy in my new job, I neglected to wash it off quickly with the obvious result. Those dang snowbirds! Haha!

Very nice looking bike! They have carbs so that means they need some choke when cold but they fire up immediately.

Which is what I try to do. I keep the engine in too low gears for the speed or too high for the speed trying to avoid the whine rpm.

Welcome! Many good knowledgeable folks on the site!

Last week was Myrtle Beach bike week. I didn't even think about it until this week. Hey Skid, were you there?

PM your phone number and I will message the photos to you or email and I will email them. I'm having trouble getting my phone to recognize my computer so I can't transfer the photos to the computer.

There has to be a demand for the skills you learn. And a year round demand at that. I don't see how a motorcycle dealership stays in business up north where the riding season is so short unless they sell snowmobiles or other winter sports equipment. When I got my chemical engineering degree in 1973, a couple of classmates didn't have jobs when they graduated. The choices I had were several opportunities in the textile industry or one offer at a nuclear power plant under construction. I'm so glad I didn't choose the textile industry because it no longer exists. Now the nuclear power industry is dying.

It's a seasonal business. When it's cold there is low demand for service/repairs. I'm sure it's hard to keep good mechanics employed year round.

If a shop works on a bike that isn't worth much and the repair bill is high, the owner might walk away and leave the bike at the shop without a way to get all the money for their time and effort. Same with working on old cars that are in bad shape. And there are always lost of stuff that need to be repaired on old cycles and cars. I understand why they don't do it. I would want to paid as I went when repairing an old clunker.

I don't think so. I asked the same question back when and I was told most just jack it up under the exhaust pipes. cringe!

Perhaps you could get the mechanic to work on it on his own time if you could get to talk to him.

Check the compression on all cylinders to make sure the engine is in good shape mechanically. Check the exhaust temps to see if all are up to temperature. It may be running on 2 cylinders. Check for spark at all cylinders by removing each plug and grounding it against the engine block and looking for spark. Also, the carbs have rubber diaphragms that have to be in good condition for the bike to get fuel above idle.

I bought some pegs like that for my Kawasaki a good while ago and I could never get them to stay in place, no matter high tight they were.

If you can repair the stuff that it will need, buy it. If you have to pay someone else to repair it, buy a newer bike. One member bought a cheap not so good 83 and had about $5,000 invested by the time it was finished because he paid someone else to repair what it needed. He seemed happy with the end result. And most shops won't work on a bike this old. Another member bought a clapped out 83 and did a frame up repair himself and it looked great afterwards. They are fast, fun bikes after you get them roadworthy.

Very Nice!

The coolant flow rate past the surface does affect heat transfer. The BWR (Boiling Water Reactor) power plants have pumps that circulate the water inside the reactor to help heat transfer from the fuel rods to the cooling water. Tweaking this flow rate also affects reactor power.

Discussions are being held about giving up patent rights to the vaccines so they can be produced by Indian pharmaceutical companies. May or may not happen.

From what I have been reading though Pennzoil is now one of the best oils on the market. Their regular oil is one of the best in the Noack volatility test and their synthetic is made from natural gas.

Be careful. Dirt riding is more likely to cause crashes than highway riding.

Give it a try. But, dirt bikes are light weight, have large front wheels, high seats, and have more suspension travel for good reasons, so it won't be an ideal dirt bike but have fun with it.