cowpuc Posted December 22, 2013 Share #1 Posted December 22, 2013 You choose the title.. Anyway,,, while responding to another thread about putting rebuilt diaphrams in I suddenly remembered a question that has popped into my mind a number of times... Have you ever noticed on a 1st gen carb that 1 of the four screws that hold the slide cover on has a special screw head?? I have thought about this a lot over the years while crossing the country on these bikes (oh come on, ya'll have to have gotten bored once in a while too)... Its kinda like the old lug nut lock to keep people from stealing wheels,,, only I dont remember a time when Carb Covers were valuable enough to get beat up for... Any thoughts? I should have searched this, knowing you guys, a masters thesis has already been written about it... Link to comment Share on other sites More sharing options...
Peder_y2k Posted December 22, 2013 Share #2 Posted December 22, 2013 Anti tamper............for those who don't have anything better to do with their time. There are special screwdrivers (dealer shop) for that screw head, but I've never seen one. I used a dremel grinder to remove the little pin down in the recess. -Pete, in Tacoma WA USA Link to comment Share on other sites More sharing options...
MiCarl Posted December 22, 2013 Share #3 Posted December 22, 2013 Anti tamper............for those who don't have anything better to do with their time. There are special screwdrivers (dealer shop) for that screw head, but I've never seen one. I used a dremel grinder to remove the little pin down in the recess. -Pete, in Tacoma WA USA Harbor Freight sells a security bit set for small $$. It has all those special tips. Link to comment Share on other sites More sharing options...
Yammer Dan Posted December 22, 2013 Share #4 Posted December 22, 2013 Harbor Freight sells a security bit set for small $$. It has all those special tips. Carl nailed this OLD question....come on Puc we covered that in 1st Gen Education 101. Where were you?? Out running around with Tippy again??? NEXT?? Link to comment Share on other sites More sharing options...
cowpuc Posted December 22, 2013 Author Share #5 Posted December 22, 2013 Carl nailed this OLD question....come on Puc we covered that in 1st Gen Education 101. Where were you?? Out running around with Tippy again??? NEXT?? I knew I was dealing with a rough crowd but,,, yea,, didnt even get off the ground with that one!! Hats off to Pete and Carl for straightening the curves on that one,, I still think its a conspiracy - maybe to sell more tools.. Got to agree with Carl about Harbor, I LOVE them for speciality tools,, remember years ago when I guy had to beg his dentist for old dental pics and jewlers lenses were out of sight (pun).. Ok tuff guy Yammer, getting tired a bumpin heads with ya,,, think I will start another trivia thread, just to see how intellectually savvy you guys really are,, I'll see your NEXT? and raise ya wo :stirthepot: Link to comment Share on other sites More sharing options...
bongobobny Posted December 22, 2013 Share #6 Posted December 22, 2013 I'm in... Link to comment Share on other sites More sharing options...
Yammer Dan Posted December 22, 2013 Share #7 Posted December 22, 2013 YEP Its WINTER!!! +65 degrees!! Link to comment Share on other sites More sharing options...
DragonRider Posted December 23, 2013 Share #8 Posted December 23, 2013 You will find that most have thrown that security screw away and replaced it with a regular screw or an Allen head, which is what I have done on my 83, and when I replace the diaphragms on my 93 trike will do the same. Link to comment Share on other sites More sharing options...
cowpuc Posted December 23, 2013 Author Share #9 Posted December 23, 2013 You will find that most have thrown that security screw away and replaced it with a regular screw or an Allen head, which is what I have done on my 83, and when I replace the diaphragms on my 93 trike will do the same. I am with you Lewis, yea,, dont put it in your spare screw drawer.. Or.. Up in garage working on a kawasaki 100 carb, pull the bowl to clean the jets, one of the bowl screws has a stripped head, walk down stairs, remove new screw from drawer, walk back up stairs, clean glasses, sit down with new screw to put in bowl,, arrrrgggg, toss that "anti-tamper screw" in neighbors yard, say a couple words you shouldnt say, walk back to get nuther screw.. Link to comment Share on other sites More sharing options...
Venturous Randy Posted December 23, 2013 Share #10 Posted December 23, 2013 The way to get that special torque head screw loose......... and the rest of the stuck, stripped head ones is........... vise grips. RandyA Link to comment Share on other sites More sharing options...
Yammer Dan Posted December 23, 2013 Share #11 Posted December 23, 2013 The way to get that special torque head screw loose......... and the rest of the stuck, stripped head ones is........... vise grips. RandyA That's what I used!!!:clap2: Link to comment Share on other sites More sharing options...
baylensman Posted February 6, 2017 Share #12 Posted February 6, 2017 I've seen a lot of that in the automotive field and in small glass engines when i switched job. Its a guvmint thing. supposed to stop us from adjusting things to avoid emission standards. It usually take about 2 years for ( special wrench or screw drivers to hit the market and circumvent the reg's. I've seen D's, double D's, 5 point star, half hex, offset oval and a bunch more since around 1971 or so. The last Lawn mower Sold had a Briggs 7.5 torque engine it had three different screw heads on the carb adjustments.Screen Shot 2017-02-06 at 9-1.46.24 AM.pdf Link to comment Share on other sites More sharing options...
snyper316 Posted February 6, 2017 Share #13 Posted February 6, 2017 Have just about all those but to ask where I put is another story, I gave up about 3 yrs ago, when they came out with a new one. Living life one curve after the other. Vroom scooting, thru the countryside. Link to comment Share on other sites More sharing options...
Yammer Dan Posted February 6, 2017 Share #14 Posted February 6, 2017 Harbor Freight has a large set of those security bits that is worth having in the garage. Link to comment Share on other sites More sharing options...
cowpuc Posted February 6, 2017 Author Share #15 Posted February 6, 2017 Harbor Freight has a large set of those security bits that is worth having in the garage. I got one of those fancy bit thingys in the form of a small punch.. I just take the punch, place it against that little nipple looking thing that protrudes in the center of the confounded secret agent security screw, give the punch a smack with my 007 framing hammer - that little nipple becomes nothing more than a short lived bump standing in the way of a good adventure out CTFWin.. Slip a normal allen wrench into the once upon a time security screw - remove and give it toss and replace it with normal, everyday, left over screw from the bike parked next to mine at a Maintenance Day event... **** ,, this is kind of an old thread ya bunch of lop eared varmints,,,,,, sure seems like one of you guru's would have come up with another,,, maybe even more , trivia question by now - thinkin 4 years should have been plenty of time for ya'll to have done so,,,,, maybe,,, maybe not:hihi: Link to comment Share on other sites More sharing options...
snyper316 Posted February 6, 2017 Share #16 Posted February 6, 2017 I got one of those fancy bit thingys in the form of a small punch.. I just take the punch, place it against that little nipple looking thing that protrudes in the center of the confounded secret agent security screw, give the punch a smack with my 007 framing hammer - that little nipple becomes nothing more than a short lived bump standing in the way of a good adventure out CTFWin.. Slip a normal allen wrench into the once upon a time security screw - remove and give it toss and replace it with normal, everyday, left over screw from the bike parked next to mine at a Maintenance Day event... **** ,, this is kind of an old thread ya bunch of lop eared varmints,,,,,, sure seems like one of you guru's would have come up with another,,, maybe even more , trivia question by now - thinkin 4 years should have been plenty of time for ya'll to have done so,,,,, maybe,,, maybe not:hihi: Remind me not to park my bike within a mile of yours.... Hate to open her up and start losing slinkies. [emoji317] Living life one curve after the other. Vroom scooting, thru the countryside. Link to comment Share on other sites More sharing options...
cowpuc Posted February 6, 2017 Author Share #17 Posted February 6, 2017 Remind me not to park my bike within a mile of yours.... Hate to open her up and start losing slinkies. [emoji317] Living life one curve after the other. Vroom scooting, thru the countryside. Sounds like a doable plan on ur part Snype except 4 the part where you n Tink get there before Tweeksis n i and she comes to a halt beside your unguarded scoot. Maybe a better plan would be to take a piece of duct tape, put an extra screw under it and stick it to the slide cover. Do this to each carb and you should be fairly safe to ride anywhere and park anywhere in the U.S. and Canada! Link to comment Share on other sites More sharing options...
videoarizona Posted February 7, 2017 Share #18 Posted February 7, 2017 Harbor Freight sells a security bit set for small $$. It has all those special tips. Be vewy, vewy careful using this kit. I used one of the "philips" bits and with very little force, it sheered off. Thankfully, I bought the kit for use with the 1st Gen carbs.....once I'm done tinkering with them, I'll put in some hex bolts/screws or whatever ya call those critters. Link to comment Share on other sites More sharing options...
Dragonslayer Posted February 7, 2017 Share #19 Posted February 7, 2017 I've seen a lot of that in the automotive field and in small glass engines when i switched job. Its a guvmint thing. supposed to stop us from adjusting things to avoid emission standards. It usually take about 2 years for ( special wrench or screw drivers to hit the market and circumvent the reg's. I've seen D's, double D's, 5 point star, half hex, offset oval and a bunch more since around 1971 or so. The last Lawn mower Sold had a Briggs 7.5 torque engine it had three different screw heads on the carb adjustments. I wasn't aware there was such things as Glass engines. I'd never seed one. But it would be cool watching everything in there spinning around while you was zooming down the road.I'm dizzy now. Link to comment Share on other sites More sharing options...
baylensman Posted February 7, 2017 Share #20 Posted February 7, 2017 Ha ha. Caught a misspelling there. yeah a glass engine would be neat. Link to comment Share on other sites More sharing options...
cowpuc Posted February 9, 2017 Author Share #21 Posted February 9, 2017 Ha ha. Caught a misspelling there. yeah a glass engine would be neat. Brings back some great memories of years long gone by,, remember that clear plastic "working" v-8 engine model that used to be advertised - for the life of me I cant remember where it was advertised but I remember drueling over the ad - maybe readers digest or mechanics illistrated of something.. Anyway,, ALWAYS wanted one - never got one - I sure led a deprived life :big-grin-emoticon::big-grin-emoticon: I am with ya Bay = a glass engine so one could watch the gizmo's gizmoeing would be AWESOME!! Link to comment Share on other sites More sharing options...
baylensman Posted February 9, 2017 Share #22 Posted February 9, 2017 Hey Puc. go over to that there new fangeled Amazon thingi the got a visable v8 and a visable wankle Link to comment Share on other sites More sharing options...
stanG Posted February 9, 2017 Share #23 Posted February 9, 2017 I think you are all missing the point here. I think the question is... Just what kind of super secret stuff is within the confines of that cover that the guru's at Yamaha wanted to prevent you from getting your greasy little fingers on? Little pieces of rubber that are prone to perforation? "Slinky" springs that will likely careen across your shop when set free? Tubular devices specially designed to get stuck at the most inopportune time and leave your VR running like crap? Pointy little needle thingies? Microscopic "c" clips and spacers that get lost on the floor of your shop? I've often pondered the need for the "wheel lock" and my conclusion is "WTF". I went over the top and replaced all the screws with stainless Allen head. Now if I could just find my Allen wrench........ Link to comment Share on other sites More sharing options...
vzuden Posted February 9, 2017 Share #24 Posted February 9, 2017 "....remember that clear plastic "working" v-8 engine model..." I assembled one of those as a kid. It was a small block chevrolet as I recall. A couple of batteries ran it and a few drops of some kind of oil kept it from seizing. If I dug deep enough in the attic I may even still have it from probably 50? years ago. Link to comment Share on other sites More sharing options...
Flyinfool Posted February 10, 2017 Share #25 Posted February 10, 2017 I had that same clear V8 model when I was a kid. Yea it was 50ish years ago. In the other hand, I have been debating replacing all 4 side covers on my 1st gen, with clear windows and have LEDs inside of the engine to illuminate it. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now