Jump to content

igya

Expired Membership
 View Profile  See their activity

  • Posts

    121

  • Joined

  • Last visited

Reputation

16 Good

Personal Information

  • Name
    CHARLES GILL

Converted

  • Home Country
    United States

Converted

  • Bike Year and Model
    1985 YAMAHA VENTURE ROYALE
  1. igya
    Don't forget to paint the inside of the cut-off with a high temp black paint after brushing out as much surface rust as possible.
  2. igya
    I'm not sure what you're talking about concerning 3 weld points on the non-chrome part. Just as the tip of the muffler starts to reduce to a cone, there's a seam. Cut on the back side of the seam (toward the rear of bike) because there's a baffle where the seam is that you need to leave in place. I left the steel tube coming through the center of the baffle about an inch long and drilled four 5/16" holes around the tube. That gave it a very powerful sound that mellows out to almost nothing at about 40mph. Keep in mind that this is a 1985 (1st generation) Venture Royale.
  3. igya
    I put this same post in the original thread but decided to do it again with a new thread since I was so slow responding to the last questions. Sorry about the delay responding. Been in south Louisiana piggin' out on Cajun cookin'! Use duct tape to protect the chrome and a sawzall (reciprocating saw) to make the cut right past the seam (on the exit side of seam) as it drops to a cone. Smooth out edges with an orbital sander. Paint the insides with high temp black paint. Be careful and don't cut into the inner pipe until you decide how far you want it to extend out of the baffle plate. Doing it this way keeps you from having to remove the mufflers. If you're nervous about cutting, leave extra metal that can be slowly ground down with a 4-1/2" angle grinder.
  4. igya
    Sorry about the delay responding. Been in south Louisiana piggin' out on Cajun cookin'! Use duct tape to protect the chrome and a sawzall (reciprocating saw) to make the cut right past the seam (on the exit side of seam) as it drops to a cone. Smooth out edges with an orbital sander. Paint the insides with high temp black paint. Be careful and don't cut into the inner pipe until you decide how far you want it to extend out of the baffle plate.
  5. igya
    For what it's worth, I have a low mile '87 1300 VR engine that I bought for a backup in case my '85 2nd gear went south. But I'm selling my VR while it's still okay. I gave $740 for the engine, but would take $550 if you picked it up in Springfield, Missouri. If interested, my email address is cwg45@sbcglobal.net.
  6. igya
    A quickie question guys. Will a seat from a 1983 VR fit on a 1985 frame? Thankymuch!
  7. igya
    I have a great set of VR1200 cams I'll take $30 (postage included) for.
  8. igya
    I've searched their site but can't find it. Do you have a link to the part?
  9. igya
    I appreciate the tip, but I would really like to beat $111.00.
  10. igya
    Well, for the THIRD time my 200 lb body took on the 750 lb '85 VR, and I don't have to tell you which one came out on top (literally). Just a parking lot/loose footing thing but enough to wipe out the plastic holder for the CB and CLASS. eBay is already being searched, but has anyone got an idea where I could get another one without getting a second mortgage? Thanks guys (and gals).
  11. igya
    Well, that was clear as mud. Try this. With all components installed, the top black plastic plate that the CB and CLASS faces stick out of, that's the part I need. Wheew!
  12. igya
    I need the plastic part that surrounds the CB and air suspension system. Now, that's the upper (or outside) plate that you see looking at with everything installed in the right side of fairing.
  13. igya
  14. igya
    Hey, you guys leave poor George alone. I know a LOT of Harley riders who have trouble spelling.
  15. igya
    Out of the 38 bikes I've owned (mostly Japanese) over the past 43 years have had standard size ND or NGK plugs. In fact, most of my cars have been Japanese, same thing.
×
×
  • Create New...