-
Posts
295 -
Joined
-
Last visited
Reputation
53 ExcellentAbout Ozlander
- Birthday 02/11/1939
Personal Information
-
Name
Merlyn Michael
location
-
Location
Rose Hill, United States
Converted
-
City
Rose Hill
Converted
-
Home Country
United States
Converted
-
Bike Year and Model
89 Venture Royale
Recent Profile Visitors
The recent visitors block is disabled and is not being shown to other users.
-
Prairiehammer started following Ozlander
-
Canadian winter - I had enough of you - I am riding my Venture to Mexico
Ozlander replied to jfman's topic in Watering Hole
Yeah, what Randy said. I've been all over North America, from below sea level to over 14,000 feet without a hiccup from the carbs. Probably diaphragms or a float. -
I did the Dingy brush ground upgrade about 10 years ago. Starter has been fine since. Probably all you need to do.
-
Clutch Slave Rebuild
Ozlander replied to Patmac6075's topic in Venture and Venture Royale Tech Talk ('83 - '93)
Looks good. Can I send you mine so you can rebuild it??? -
Need new water hoses
Ozlander replied to zoomjay's topic in Venture and Venture Royale Tech Talk ('83 - '93)
Mine came today. Ordered from China, came from Steve Xu, West Chester, Ohio Look OK, have not tried them. -
What I learned about my "89 VR
Ozlander replied to Ozlander's topic in Venture and Venture Royale Tech Talk ('83 - '93)
Maybe this will work. Venture with MAP sensor 4.zip -
What I learned about my "89 VR
Ozlander replied to Ozlander's topic in Venture and Venture Royale Tech Talk ('83 - '93)
I can send you the program for the IgniTech that I'm using if you want. I tried to attach it here, but can't. I'll email it to you. -
Need new water hoses
Ozlander replied to zoomjay's topic in Venture and Venture Royale Tech Talk ('83 - '93)
I ordered a set. I figured for 34 bucks, enough would fit to make to worth while. I let you know what happens. Mine are 27 years old, seem to be in good shape, but who knows? -
What I learned about my "89 VR
Ozlander replied to Ozlander's topic in Venture and Venture Royale Tech Talk ('83 - '93)
Not really, I tried all kinds of restrictors and wire inside the restrictor to make the orifice smaller. The problem is, one intake cycle sucking and three cycles leaking the vacuum. If you don't use a vacuum gauge, you don't see this. If you look at the advance with your computer hooked up the IgnTech, you'll see it jumping all over the place. I fixed that. -
What I learned about my ’89 VR this summer. Went to the MTA Rally in Georgia last June and then to my BIL in Jacksonville, NC. Rode the Tail of the Dragon, which is a bunch of hype. 3003 miles pulling a trailer Finally, after 25 years, I learned how to reset the cruise control. Before, if it was set to a speed and engaged, I was having trouble resetting the speed, either up or down. I found that I released it, (touched the brake or clutch), it would reset to whatever the new speed was. I’ve been during a lot of reprogramming the IgniTech ignition I got from Dingy. I did some riding with a vacuum gauge noting vacuum readings at different rpms and throttle settings. Could not get a wide range of vacuum readings. Finally, I installed a check valve in each of the 4 hoses from the vacuum ports to the MAP sensor. Finally, a full range of values from 5 to 28 in/hg. Using those readings, I reprogrammed the IgnTech. I also dropped the needles a 1/16” in the carbs and checked float level. During the trip I was getting around 35 mpg pulling a trailer at 70-75 mph and 45 mpg without the trailer. Leaving NC to come home, I found I had a burned out stator. Ordered one from Denis Kirk and had it overnighted in. They were the only ones who seemed to have it in stock so we didn’t have to wait very long, but cost me about twice as much. They even called me to verify the shipping address. Luckly, my bil has an impact screwdriver which is almost a requirement for removing the stator screws. Even so, one of the short screws was damaged enough that I didn’t want it to come loose and bounce around inside the stator. Went to LOWES and found a metric allen head screw to replace it. Took the same allen wrench as the case screws. Thinking ahead, I may start carrying a spare stator like some of my Goldwing friend do. By replacing the stator screws with allen head screws, I would have all the tools I need in my tool kit.
-
Need new water hoses
Ozlander replied to zoomjay's topic in Venture and Venture Royale Tech Talk ('83 - '93)
For $33 I would try some, but I can't figure out the web site. Should be able to get them direct from china, but can't find them US Shipping in West Chester, Ohio has them for 54 bucks on e-bay. Go here http://www.aliexpress.com/item/Silicone-Radiator-Heater-Hose-Fit-For-YAMAHA-VMAX-VMX12-Black/32213640758.html?spm=2114.01020208.3.52.Q2DuYI&ws_ab_test=searchweb201556_3,searchweb201644_1_10014_10001_10002_10005_301_10006_10003_10004_62_61,searchweb201560_8,searchweb1451318400_6151,searchweb1451318411_6450&btsid=8aec4063-eed5-4667-8e0b-a07120dbc0bf -
Looking for new roads to ride? Check here. http://www.motorcycleroads.com/
-
Same here.