Jump to content


Supporting Member
  • Posts

  • Joined

  • Last visited


192 Excellent

Personal Information

  • Name


  • Location
    MKE, WI, United States


  • City


  • State/Province


  • Home Country
    United States


  • Bike Year and Model
    1984 Venture

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Welcome Elton, The air ride system on the Venture Royale only operates when the key is in the acc position. I’m 5’8” with a 30” inseam and this bike is a tad tall for me. I rarely am able to stand flat footed at a stop light. Some years back I heard tell of a member who shaved some padding from the seat to help lower the stand over height.
  2. Sorry for the absence, life gets in the way sometimes. Cowpuc wins the prize! Hand impact won out (was also the first thing I tried). I retightened the lower of the two bolts and gave the upper bolts a couple medium tappy-taps to tighten, then changed direction to loosen and let loose with a 3lb maul. Came right undone (even on the stripped out one)!Thanks guys! As a side note my bearings had some notchyness in there (I’m certain they were OE), and after pulling them out, the grease was like glue. Also, those races are fighting me every step of the way (can gain almost zero purchase, even with that little cutout they give you)…I’ve gone the destructive route and started cutting them with a dremel. I’ll update when I have more. thanks again Pat
  3. Thanks! I’ll update when I get back to it this weekend
  4. Thanks for the response Carl, there are 2 pinch bolts on the upper tree and the lower tree. I was able to loosen the 2 bolts on the upper tree. There are 2 bolts on the lower tree (a lower bolt and an upper bolt), I am having trouble with the upper bolt on the lower tree…both sides.
  5. So I finally decided to replace my steering bearings…started loosening the (fork tube) pinch bolts on the top and bottom of the triple tree…I had no problem with the top pinch bolts, and really had no issue with one of pinch bolts on the bottom (the lower of the two on each side), but the upper Allen bolts ON BOTH SIDES are just so tight, I’ve stripped one out and fear I’ll strip the other out if wrench on it any more than I have. I thought maybe I could just remove the main steering nut and slide the lower triple tree out (still attached to the fork tube), but I seem to remember there is a small clip on the upper triple tree that needs to be removed before the tubes will slide out. Any ideas? I’ve used an impact, I’ve tried a long lever (with a constant even torque), I’ve used penetrating oil….although I haven’t tried heat (concerned I might melt fork seals).
  6. I have a routine I do every year… 1. Do a deep clean of the bike and fill the tank with non-ethanol gas with 1/4 can of SeaFoam (it can be used as a stabilizer as well) 2. Change oil and Filter as well as clean and re-oil the air filter (it’s a K&N, please don’t judge me) 3. Replace with new properly gapped spark plugs, I also spray the inside of the cylinders with SeaFoam spray 4. I disconnect the battery and put it on a tender 5. Finally I put the bike on the center stand with a Jack stand under the front center member to get both tires off the ground Now I live up in Wisconsin so, once I put my bike up for the winter, chances are it’s not coming out until Spring. But my bike fires up no problem once I take her out.
  7. A couple of years back I’d replaced all of my dash bulbs with LEDs. I can’t recall the part numbers, but they were readily available and relatively inexpensive. Pretty sure I got them at a place called Superbrightleds.com , it was pretty easy to cross reference them, I may have even talk to their customer service. My one piece of advise….don’t put a white bulb behind a colored lens…if it shines through a green lens, get a green bulb. If it shines through a red lens get a red bulb. Also one tip to others so you don’t make the same mistake I did…I replaced my warm white dash bulbs with red, although it looks really cool….it’s functionality leaves something to be desired. My dash at night is somewhat difficult to read. Luckily I don’t do that much night riding.
  8. Thanks Jeff! I’m now in Greendale…so if’s you’re ever just wandering around let me know!
  9. Thanks Saddlebum….it worked! Kind of one of those “mixed emotions” moments….I’m totally stoked it worked, on the other hand….I’m bummed that I bought a new retainer spring ($10 for the part and $10 to ship…thanks partzilla). No matter, it’s back together and all because of the helpful crew here on the site. Thank you
  10. Thanks Saddlebum….to be clear…I need to take the wire retainer off again! And remove both ot washers on either side of the 1/2 disc? Thanks…
  11. Ok, so it’s not that bad, but getting that clutch boss spring-a-ma-jig thing back on was way tougher than I’d expected. So I was looking for those markings (in some cases dots, in others square cut outs)on the clutch fiber plates to line up with the clutch boss….I don’t see anything resembling marking on the Barnett clutch fiber plates! So I just set them in there as they came out of the oil bath….Is this going to be a problem? Second issue, just got it all reassembled and I cannot pull the clutch lever in? Are these two issues related? What’s the work around? Also, just to be certain, I did not mess with the pushrod or ball bearing…as far as I know, they didn’t even move. Your input will be most appreciated Pat
  12. Ha ha….I prefer SeaFoam….ask 10 other members and you’re likely to get 10 different opinions, kind of like if you ask which oil is the best or which tires are the best. The reality is, you tend to stick with what has worked for you in the past. In a past life I was a regional commercial sales manager for a national auto parts chain. I had the opportunity to work with the national sales manager for SeaFoam…great guy…he got me hooked on all their products, interesting side bar…SeaFoam, Deep Creep, and their Trans fix are all pretty much the same active ingredient in different concentrations. I also love their other product Bug-b-Gone for removing bug spatter from my bike (although it’s a completely different product than SeaFoam).
  13. Just reread your original post….I wouldn’t try to put in a tank sealant in unless I was positive it was rusted through and only as a last resort. You’ll need to pull the tank in order slosh the cleaner/etch and the sealant around the tank. Again, in my opinion, draining as much as you can and refilling with fresh clean gas plus repeated fill ups should clean out any old funky gas (plus the added benefit of extra ride time). And a clean new filter should take care of most of the particulate matter. Sorry for the double post
  14. It’s been a long time since I was down there, but why couldn’t you just pull the fuel line before the fuel pump and let gravity do its job? While you’re down there you should also replace your filter. You may not get 100% of the old fuel out, but you’ll get a good portion….once you’re up and running and have run through a few tankfuls you’ll have gotten rid of most of the old varnish and gels (especially if you run some SeaFoam through with every fill up). Keep an eye on you fuel filter and maybe proactively change it out after 10-15 tankfuls. After that…keep your tank topped up and use non-ethanol 100% gasoline…you should be fine.
  • Create New...