Jump to content

rrod1393

Expired Membership
  • Posts

    48
  • Joined

  • Last visited

Everything posted by rrod1393

  1. 1984 VR. I will check the lock to look for a seal. Just wanted to get a feel if I'm the only one experiencing this.
  2. No I dont. Where the aluminum trim that seals the bag with some what of a tongue and groove, there is no weather striping. Ill have to take a photo of it when I get home. Neither bag has it.
  3. Does anyone else have water in their saddlebags after it rains? Is there a fix?
  4. Great stuff. I will get to it when I get back from Tennessee. I ended up rented a bike from HD and doing the Gatlinburg Loop and Tail of the Dragon. Looking forward to getting the bike back on the road when I get home. Thanks again for the help. I will report back with my findings.
  5. yea the one i repaired (bottom right) is hanging up or not performing the same as the others. I'm glad they are easy to swap out. I do have to sync the carbs. I'm sure that is a big problem.
  6. The bike was running when I bought it. Obviously it wasn't running well with two stuck carb slides. Everyone on this form was saying how snappy the bike is and I wasn't getting that feeling so pulled it apart. I have changes the oil and oil filter, air filter is clean enough and new plugs. I have not done a compression test. I have been busy with fixing the cruise control and other minor things.
  7. Not celebrating yet.... but I believe it will work. But I am purchasing two from a fellow member.
  8. Still have a little bit of tweaking to do but looks like it might work.
  9. I am not giving up! I have done crazier things. Its a product similar to JB weld. I don't have a ton of hope but its worth a shot.
  10. Good information. I will re-evaluate the intake boots once I get a replacement slide.
  11. But I'm still scratching my head over why they were tight. I don't really know how they were when pulling them apart but sure noticed it putting them back together. Any of you guys ever had this problem?
  12. Great. My boots are fine (i think). I really need the plastic part because the is what shattered. I have never swapped the rubber boot on the slides before but I am assuming its straight forward. Especially now the I have one in pieces in front of me.
  13. Sorry I guess I was not clear. Its the intake boots that are cracked. But I appreciate the effort. Im shocked at the cost of the slides $$$$$$$
  14. So I just went back out to the garage because I was wondering if maybe I put the vent hole on the slide backwards (if it matters). So I found that the slide and diaphragm came apart in the carb which Ive never seen before. While trying to squeeze it back together, it shattered in my hand. Not happy. So I pulled apart the other one that was not working and found it to be loose as well. Even after squeezing it back together I could still spin the diaphragm around. Does anyone have two slides laying around?
  15. So I just pulled the carbs of the bike today, cleaned them out and returned them back to the bike. When pulling them apart, I noticed that the rubber diaphragm on the carb slide was loose and spinning on the slide. Noticing that the metal insert was pulled out a bit, I pushed it back in, tightening the rubber again as it should be. Putting the carbs back together I noticed that the slides were rather tight. They would not drop right in as I'm used to on other bikes. I took a green scotch brite pad and polished the interior of the carb and wiped clean. This seems to do better and once all together the slide would go up and down. I wasn't thrilled will how it when together but it seemed like it would work. Got the bike running and two of the four slides stopped moving all together. While pulling the carbs, I notice that the boots have a tiny crack so theres that issues now but I believe the slide should not be affected by the small vacuum leak from the boots. Any one ever have this issue? Oil on the slide did not seem to help. I hope to post a video of it soon. Where should I get boots from?
  16. Were you able to solve the problem or is it something you just live with?
  17. Mine does the same. When I let go of the handlebars it wants to turn left. Was the steering bearings the issue for you? Is there a special tool required to tighten the bearing?
  18. Does any one have an extra petcock handle to sell me? I know I have a fuel gauge but I feel more warm and fuzzy knowing that I have a reserve tank available if needed.
  19. Having the same issue with my rear suspension. The bike will not adjust while ride because the Class system (air ride) is not on while the key is in the ON position. Lot of guys will recommend taking apart the three solenoids in the controller to make sure there is no corrosion and giving them a good cleaning if there is. I did this and now my rear air leaks out quicker. I believe that one of the solenoids isn't seating properly when closed. Spray some soapy water around and see if you get lucky enough and find a leak. good luck.
  20. I just checked mine and found that the bolt was tight but the stand (when extended) had a lot of up and down play. I think the clamp has widen from a loose bolt and the bike's weight leaning on it. Is that the play that this thread wants me to address??
×
×
  • Create New...