Jump to content
IGNORED

Installing an Aux line splitter


Squidley

Recommended Posts

Well I have some time and decided that I will put up how to split the front fairing and install the audio cable to hook up MP3 players, Sat radio or GPS units. This is not a hard thing to do and it just takes a little time.

 

Here is what you will need to accomplish this, all these cables can be purchased at you local Radio Shack for less that $20

 

2 Way splitter part # 42-2570

 

image.jpeg.bc9633e502500961e67b8f3e64277022.jpeg

 

6 FT Audio Cable part # 42-2387A

 

image.jpeg.892e6a9d25f227cb44772034cc288594.jpeg

 

You can also use a 3 way splitter if you choose for more hookups Part # 42-2458

 

image.jpeg.8103f1e1835dd3eb1f5cdf69977a3000.jpeg

 

and if you want the ultimate audio cable then here is the gold series 6 FT cable Part # 42-2607

 

image.jpeg.bd1492863d7f7f6b27355a79e0707c86.jpeg

 

 

 

First thing to do is take off the chrome windshiled trim, it is held on by 2-3mm hex bolts (Pic) when you remove the bolts you need to get your fingernails under both outer edges of the chrome piece and lift strait up, working it slowly. You can rock it back & forth strait up and this will help it along. If yours has never been off it will go a little hard and your going to be puckered. Dont force it! work it a bit and it will come off.

 

image.jpeg.fee4460cda2749b0198b428413206b5c.jpeg

 

Next is to remove the additional 6 bolts that hold the fairing on from behind, there are 3 on each side and are 3mm also,

 

image.jpeg.bc7b2e708a251490e5e0681f515cc8db.jpeg

 

You'll also notice that the 2 bolts that hold the chrome windshield trim on are longer than the others, they need to go back in those 2 top holes on reassembly

 

image.jpeg.cb1f5dadd171068d33cd828fb69dc8b9.jpeg

 

The next bolt to remove is the 4mm below the headlight

 

image.jpeg.2491f0385ab51698ce00e364dedc2b0d.jpeg

 

You will see 6-3mm bolts along the top of the fairing, these hold the windshield on and the top of the fairing.

 

 

 

There is a trick here, remove the 1st bolt to the right of the center completely out. Then you will loosen the remaining 5 but dont take them completely out.

 

image.jpeg.5c239f48e5688a1966a710b9201f20e2.jpeg

 

You will see that the windshield has slots and that it slides over the other bolts. Once you have them loose and the one out you can lift the shield strait up and off the bike.

 

image.jpeg.fe7e52f9b06d6e6117973fbc37d31383.jpeg

 

Take out the remaining bolts and you can now remove the fairing. If you have driving lights that are not on an extention you will have to take the bracket loose to remove the front of the fairing. Now the bike will look like this

 

image.jpeg.0c5689f79fc1beb9dd1226d8adcc2f3c.jpeg

 

You will now have to dig around inside the wires to free up the connectors for the Aux jack, here is the wire to which it is connected on the amplifier unit. This wire has the female end on it and is what you will plug the new splitter into.

 

image.jpeg.78a2e6173e1544efa7d455939c4de45a.jpeg

 

And here is the male plug that goes to the back of the cassette deck. You will plug this into 1 of the female ends of the splitter should you want to hook up the aux jack behind the cassette door.

 

image.jpeg.db9f084f2750ff98e4ad5187be42118a.jpeg

 

What you now need to do is take your splitter, which you can get from your local Radio Shack and install it onto the female end that is on the amp.

 

image.jpeg.ba3f5f5289a3fc9493ae897c6fac3e47.jpeg

 

image.jpeg.623fea95bb567ad542af903c0db4b55a.jpeg

 

I just wrapped it in electrical tape for seal out any moisture and debris.

 

image.jpeg.2948acd2c3931945e18c2fec1ceae4a2.jpeg

 

Now you can plug the male end from the casstette deck back into the splitter so it's still useable if you wish. Remember to wrap it in electrical tape so it is sealed and wont be pulled apart.

 

You can now plug in your 6 ft Audio Cable that you will be running to whatever device your hooking up MP3 GPS or Sattilite radio. If you want to hook up 2 of these then just omit hooking the tape deck line back up and purchase 2-6 ft leads.

 

You will then need to run your Audio Cable from inside the fairing to the handlebars or where ever you are hooking your components up at. I had mine run throught the cable loops that the bikes wiring and cables run through. There will be some extra length with these audio cables, just wind them up inside the fairing and put a zip tie on them to keep them neat and orderly...it makes getting around so much easier when you have to go back in there.

 

image.jpeg.f153feeedc98e7d00cbb7e599fa64384.jpeg

 

image.jpeg.e4bd10f6589d8a3563bd2d97527ec907.jpeg

 

Once you run your Audio Cables your ready to put the fairing back together, here is a little trick that will help you out. Put the outer 2 bolts in the upper fairing and start to thread them in before you slide the windshield back down into place. Many times the small brackets that hold the steel backing plate are broken and when you try to install the windshield it pushes the threaded guide holes out of position...dont ask how I know this.

 

image.jpeg.2e8f74c540d4351785e0f6f241f41bec.jpeg

 

image.jpeg.9152f46868498690034a3abd416cd2eb.jpeg

 

Install the windshield and then the right of center bolt, now the shield wont fall out. Replace all the additional bolts but be sure not to tighten any all the way up until all the bolts are threaded in....Tighten all the bolts

 

Thats all there is to it! you now have additional hookups for the aux position. Mind you this will not work with the CD changer in the bike if you have one as it will use the auxillary on the bike. This works great for MP3 players, GPS systems and Sat radio.

Link to comment
Share on other sites

×
×
  • Create New...