Member Vendors Latest Topics

SECOND GEN. S.S. BRAKE AND CLUTCH UPGRADE LINE SET!

Wed, 22 Feb 2023 01:21:34 +0000

WITH THE SECOND GENS. BEING OUT OF PRODUCTION SINCE 2013, THIS MEANS THAT THERE COULD BE SECOND GENS. OUT THERE WITH BRAKE AND CLUTCH LINES THAT ARE 24 YEARS OLD! IN AN EFFORT TO KEEP THESE BIKES SAFELY ON THE ROAD, I HAVE CREATED A REPLACEMENT BRAIDED S.S. LINE TO REPLACE EVERY BRAKE AND CLUTCH LINE ON YOUR MOTORCYCLE.

THIS S.S. LINE SET IS A DIRECT BOLT ON REPLACEMENT, THAT REQUIRES NO MODIFICATIONS TO THE BRAKE OR CLUTCH MASTER CYLINDERS OR THE CLUTCH SLAVE CYLINDER OR BRAKE CALIPERS! IN THE PIC BELOW THE LINES ARE MARKED “A” THRU “E”.

LINE A- LOWER RIGHT AND LEFT FRONT BRAKE CALIPER LINE.

LINE B- REAR BRAKE CALIPER LINE.

LINE C- UPPER BRAKE MASTER CYLINDER LINE.

LINE D- UPPER CLUTCH MASTER CYLINDER LINE.

LINE E- LOWER CLUTCH SLAVE CYLINDER LINE.

THE COST FOR THIS S.S. LINE SET IS $250.00 WITH FREE SHIPPING IN THE LOWER 48 STATES. OUT OF THE COUNTRY SHIPPING WOULD BE ACTUAL SHIPPING COSTS. I DON’T MARK UP SHIPPING COSTS FOR THE INTERNATIONAL FORUM MEMBERS! I ACCEPT PAYPAL AND PERSONAL CHECKS FOR PAYMENT. I CAN ALSO PROVIDE R1/R6 4 PISTON CALIPERS AND HIGH PERFORMANCE BRAKE PADS TO FURTHER INCREASE THIS UPGRADE!

THANKS FOR VIEWING MY AD! SKYDOC_17.

Second Gen. Heavy Duty Clutch Spring & Full Disc Upgrade Kit!

Sun, 11 Nov 2018 01:37:30 +0000

When you roll on the throttle of your Second Gen. RSV or RSTD does the

clutch slip? When you "briskly" go from first to second gear does your

clutch slip? Do you ride 2 up often? Are you trying to pull a trailer and is

your clutch slipping? Are you thinking about paying $300.00 plus the

install for a Barnett Clutch, well think again! The stock Yamaha clutch is

a high quality part and will last up to 100,000 miles. The problem is not

your clutch; It's the clutch basket diaphragm spring and that "wimpy"

half disc that has failed. So here's the fix! Install an aftermarket, thicker

clutch diaphragm spring, and full clutch disc and never worry about that

RSV or RSTD or RSTC clutch again! The heavy duty clutch diaphragm spring

puts 25% more clamping force on the clutch discs than the stock RSV

clutch spring. Here's my deal, you get a brand new .070” thick heavy duty

clutch diaphragm spring, (name brand) a new full clutch friction disc to

replace the half disc, and a brand new, genuine Yamaha replacement

clutch cover gasket, everything you need to do this install for $115.00

including shipping in the USA!!! I will include complete written

instructions, and i have a picture file that can be downloaded!

what a deal!! If you have some miles on your current set of friction discs,

check my other MEMBER VENDOR Classified Ads for the remaining 7 genuine Yamaha friction

discs or the seven steel clutch plates for $105.00 a set each, Making this upgrade basically, a brand new, better that

stock clutch! This upgrade can be done in less than 2 hours, doesn't

require the removal of the clutch basket, can be done with a 10mm

and 12mm wrench and an allen wrench, and a pair of needle nosed pliers

and side cutters and you will loose very little engine oil! Shipping in the

48 states is free, outside the us is at actual cost! I accept paypal and checks!

Thanks for viewing my ad.

Earl (skydoc_17)

VALVE ADJUSTMENT Shim Kit Loan with Valve Cover Gaskets!

Thu, 06 Jun 2019 07:00:44 +0000

I do loan out my Shim Kit to the VR.ORG members. Here's how it works. For $100.00 via PayPal, I send you my Shim Kit that has the Bucket Tool and every other tool you will need to do the Valve Adjustment along with 80+ assorted shims and a set of Genuine Yamaha Valve Cover Gaskets by USPS Insured Priority Mail with $300.00 Ins. I allow 2 full weeks for the Valve Adjustment, (three weekends) It's not a big deal if you need the Shim Kit a bit longer, you just need to let me know. If you use a shim from my kit, you replace it with the shim you take from your bike. (size doesn't matter) If on the off chance you would accidentally break the Bucket Tool, you would do the right thing and replace it. (The only time this has ever happened is when someone used the starter motor to rotate the engine to the next valve, one time) Even though there are 80 shims in the kit, there maybe that one odd ball shim that you will need to buy or trade for from the dealer. Be prepared for this. If at the end of your adjustment you have extra shims, and want to donate them to the shim kit, that would be great. When you have finished, you will return the Shim Kit to me via USPS Insured Priority Mail Service with $300.00 Ins. on the package. If you are OK with the above terms, then a PayPal Payment of $100.00 to earlfharrell@atlanticbb.net gets the Shim Kit and the gaskets shipped right out.

This is a "first come, first served" arrangement. Thanks for viewing my ad. skydoc_17

First Gen. VR (1983 TO 1993) Fuse Box Upgrade Kit!

Sun, 11 Nov 2018 02:52:01 +0000

If your old, glass tube fuse box is shot I have the answer for you. I have compiled every item you will need to change your tired, old glass tube fuse box over to a modern ATC type fuse box. Not only does this ATC fuse box have an extra fuse slot for that set of running lights you want to add, or a new GPS, but it comes with two terminal blocks for switched power and one for battery ground. You can add many accessories, all protected by a fuse with this kit. This kit comes complete with every part you will need plus detailed written instructions and an electrical diagram. There is no soldering needed to install this fuse box upgrade! The price is $75.00 with free 48 state USA shipping. Out of country buyers will pay actual shipping costs only! I accept PayPal and Checks!

Thanks for viewing my ad!

Earl (skydoc_17)

FIRST GEN. MKII (86’ to 93’) HEAVY DUTY CLUTCH SPRING UPGRADE KIT!

Sun, 11 Nov 2018 02:35:44 +0000

When you roll on the throttle of your First Gen. MKII (1986 to 1993) does the clutch slip? When you "briskly" go from first to second gear does your clutch slip? Do you ride 2 up often? Are you trying to pull a trailer and is your clutch slipping? Are you thinking about paying $300.00 plus the install for a Barnett Clutch, well think again! The stock Yamaha Clutch is a high quality part and will last up to 100,000 miles. The problem is not your clutch, it's the Clutch Basket Diaphragm Spring that has failed. So here's the fix! Install an aftermarket, thicker Clutch Diaphragm Spring, and Full Clutch Disc and never worry about that First Gen. MKII clutch again! The heavy duty clutch diaphragm spring puts 25% more clamping force on the clutch discs than the stock First Gen. MKII Clutch Spring. Here's my deal, you get a brand new .070 thick Heavy Duty Clutch Diaphragm Spring, (Name Brand) a new full size clutch disc to replace the half disc, and a brand new, Genuine Yamaha replacement Clutch Cover Gasket, everything you need to do this install for $115.00 including shipping in the USA!!! Out of the country buyers will pay actual shipping costs only! If you have some miles on your current set of Friction Discs, or they are 20 plus years old, I will throw in the remaining 7 Genuine Yamaha Friction Discs or the 7 Steel Clutch Plates for $105.00 a set each, making this upgrade basically, a brand new, better that stock clutch! I will include complete written instructions, and I have a picture file that can be downloaded!

What a deal!! This upgrade can be done in a few hours, doesn't require the removal of the Clutch Basket, can be done with a 10mm and 12mm wrench and an allen wrench, and a pair of needle nosed pliers and side cutters and you will not loose a drop of engine oil! I accept Paypal and Checks!

Thanks for viewing my ad.

Earl (skydoc_17)

First gen. Crankcase vent filter upgrade!

Wed, 25 Dec 2019 18:39:51 +0000

THE LAST TIME YOU CHECKED YOUR AIR FILTER WAS THERE OIL IN YOUR AIR BOX?

ARE YOU TIRED OF TRYING TO GET THE AIR BOX VENT TUBE BACK ON THE CRANKCASE VENT WHEN YOU REMOVE THE AIR BOX?

WELL, HERE'S THE ANSWER! THE CRANKCASE VENT FILTER UPGRADE!

REMOVE ALL OF THAT PLUMBING THAT CLUTTERS UP THE UNDERSIDE OF YOUR AIR BOX,

STOP COLLECTING OIL IN THE AIR BOX AND GIVE YOUR ENGINE A SHOT OF "CLEAN AIR" INSTEAD OF AIR FULL OF OIL MIST. THIS

HIGH QUALITY, WASHABLE, REUSABLE CRANKCASE VENT FILTER COMES WITH VACUUM PLUGS TO SEAL OFF THE STOCK AIR BOX

AND COMES WITH ITS OWN MOUNTING CLAMP. THE PRICE IS $40.00 WITH FREE USA SHIPPING. THE INSTALL TAKES LESS THAN 30

MINUTES AND CAN BE DONE WITHOUT REMOVING THE AIR BOX. FULL WRITTEN INSTRUCTIONS ARE INCLUDED. YOU CAN CONTACT

ME AT: skydoc17@gmail.com IF YOU HAVE ANY QUESTIONS! THANKS FOR VIEWING MY AD!

FIRST GEN. MKI (83’ to 85’) HEAVY DUTY CLUTCH SPRINGS UPGRADE KIT!

Thu, 26 Dec 2019 02:51:55 +0000

WHEN YOU ROLL ON THE THROTTLE OF YOUR FIRST GEN. MKI (1983 TO 1985) DOES THE CLUTCH

SLIP? WHEN YOU "BRISKLY" GO FROM FIRST TO SECOND GEAR DOES YOUR CLUTCH SLIP? DO

YOU RIDE 2 UP OFTEN? ARE YOU TRYING TO PULL A TRAILER AND IS YOUR CLUTCH

SLIPPING? ARE YOU THINKING ABOUT PAYING $300.00 PLUS THE INSTALL FOR A BARNETT

CLUTCH,WELL THINK AGAIN! THE STOCK YAMAHA CLUTCH IS A HIGH QUALITY UNIT AND WILL

LAST OVER 100,000 MILES. THE PROBLEM IS NOT YOUR CLUTCH, IT'S THE 6 CLUTCH

COMPRESSION SPRINGS THAT HAVE FAILED. SO HERE'S THEFIX! INSTALL AN AFTERMARKET,

THICKER SET OF CLUTCH COMPRESSION SPRINGS, AND FULL CLUTCH DISC AND NEVER WORRY

ABOUT THAT FIRST GEN. MKI CLUTCH AGAIN! THE 6 HEAVY DUTY CLUTCH COMPRESSION

SPRINGSPUT 25% MORE CLAMPING FORCE ON THE CLUTCH DISCS THAN THE STOCK FIRST GEN.

MKI CLUTCH SPRINGS. HERE'S MY DEAL, YOU GET A SET OF BRAND NEW HEAVY DUTY CLUTCH

COMPRESSION SPRINGS, (NAME BRAND) A NEW FULL SIZE CLUTCH DISC TO REPLACE THE HALF

DISC, AND A BRAND NEW, GENUINE YAMAHA REPLACEMENT CLUTCH COVER GASKET,

EVERYTHING YOU NEED TO DO THIS INSTALL FOR $85.00 INCLUDING SHIPPING IN THE USA!!!

OUT OF THE COUNTRY BUYERS WILL PAY ACTUAL SHIPPING COSTS ONLY!

IF YOU HAVE SOME MILES ON YOUR CURRENT SET OF FRICTION DISCS, OR THEY ARE OVER 30

YEARS OLD, I WILL THROW IN THE REMAINING 7 GENUINE YAMAHA FRICTION DISCS or the 7 STEEL

CLUTCH PLATES FOR $105.00 A SET EACH, MAKING THIS UPGRADE BASICALLY, A BRAND NEW,

BETTER THAN STOCK CLUTCH!

I WILL INCLUDE COMPLETE WRITTEN INSTRUCTIONS, AND I HAVE A PICTURE FILE THAT CAN BE

DOWNLOADED! WHAT A DEAL! THIS UPGRADE CAN BE DONE IN A FEW HOURS, DOESN'T REQUIRE THE

REMOVAL OF THE CLUTCH BASKET, CAN BE DONE WITH A 10MM AND 12MM WRENCH AN ALLEN WRENCH

AND A PAIR OF SIDE CUTTERS AND NEEDLE NOSED PLIERS AND YOU WON'T LOOSE A BIT OF ENGINE OIL.

YOU CAN CONTACT ME AT: skydoc17@gmail.com IF YOU HAVE ANY QUESTIONS. THANKS FOR VIEWING MY AD,

EARL.

First gen. (1983-1993) radiator drain upgrade kit!

Thu, 06 Jun 2019 06:43:52 +0000

Does your First Gen. VR have that “pesky” coolant leak up by the front tire, well here’s the fix!

A new o’ring and an upgraded stainless steel allen cap screw and S.S. Lock washer.

Just install, and no more leak!

The price is $15.00 with shipping included to the USA, out of the country will be actual

shipping cost only.

This kit comes with complete written instructions, what a deal! I accept paypal and checks!

Thanks for viewing my ad! skydoc_17

First gen. (1983 to 1993) vr needle shim mod kit

Thu, 06 Jun 2019 06:26:26 +0000

Is your First Gen. VR getting less than average gas mileage? Are your exhaust pipes sooty? Can you smell gas after your bike has been running for a while? Well, i have the fix for you. Reshim your main jet needles to lean out the air/fuel mixture. This will increase gas mileage,and clean up those exhaust pipes. Others have re-shimmed the main jet needles with extra s.s. Washers, but this just adds weight to the end of the carb. Slider, slowing down the slider action and making throttle response “sluggish”. By using a nylon shim that has been precision machined, there is no additional weight to the end of the slider. This kit comes with complete written instructions, and can be done in about an hour using basic hand tools. The cost is $15.00 with shipping included in the usa. Out of the country shipping is actual shipping cost only! I accept paypal and checks! thanks for viewing my ad! skydoc_17

6 Line First Gen. S.S. Brake Line DeLink Kit with Upper and Lower Clutch Lines!

Sun, 11 Nov 2018 03:37:15 +0000

DO YOU STILL HAVE 25 PLUS YEAR OLD STOCK, RUBBER BRAKE AND CLUTCH LINES ON YOUR FIRST GEN. VR? DID YOU EVER WISH THAT YOUR FRONT RIGHT BRAKE LEVER WORKED BOTH FRONT BRAKE CALIPERS, AND THE FOOT PEDAL WORKED THE REAR BRAKE CALIPER ONLY? WELL, HERE IS THE ANSWER YOU HAVE BEEN WAITING FOR! I AM OFFERING 4 CUSTOM MADE STAINLESS STEEL BRAKE LINES THAT ARE KEVLAR LINED, WITH ALL NEW BANJO BOLTS, AND ALL NEW CRUSHWASHERS. PLUS A MATCHING SET OF S.S. UPPER AND LOWER CLUTCH LINES! ONE SPECIALLY MACHINED VMAX FRONT BRAKE SPLITTER, A POLISHED S.S. ADAPTER BRACKET FOR THE FRONT BRAKE SPLITTER, AND THE BLOCK OFF BOLTS FOR THE REAR MASTER CYLINDER AND PROPORTIONING VALVE! PLUS COMPLETE INSTALL INSTRUCTIONS! THIS S.S. LINE SET WILL REPLACE EVERY RUBBER LINE ON YOUR BIKE WITH S.S. KEVLAR LINED LINES WITH ALL OF THE HARDWARE YOU NEED! WHAT A DEAL! THE COST IS $300.00 WITH FREE SHIPPING TO THE LOWER 48. INTERNATIONAL SHIPPING IS ACTUAL SHIPPING COSTS ONLY. I ACCEPT PAYPAL AND CHECKS! (MKI OWNERS NEED TWO ADDITIONAL S.S. LINES FOR THE ANTI-DIVE VALVES ON THE FRONT FORKS, THE COST FOR THOSE LINES IS AN ADDITIONAL $50.00)

THANKS FOR VIEWING MY AD.

EARL (skydoc_17)

First and Second Gen. 7 New Genuine Yamaha Clutch Friction Discs!

Sun, 11 Nov 2018 02:01:26 +0000

If you have recently purchased one of my Clutch Spring Upgrade Kits for your First Gen. VR (1983 to 1993), or Second Gen. RSV or RSTD or RSTC

(1996 to 2013) then these 7 brand new Genuine Yamaha Clutch Friction Discs will basically give you a brand new clutch when added to one of my clutch spring kits. These clutch friction discs work on the MKI and MKII VR's and all of the Second Gen. RSV’s, RSTD’s, and RSTC’s. If you purchase these friction discs with one of my clutch spring kits, the price is $105.00 with NO additional shipping costs, if you buy them separate, the cost is $15.00 extra for USPS Insured, Priority Mail Shipping. (shipping outside the lower 48 states is at actual cost) I accept PayPal and Checks!

Thanks for viewing my ad.

Earl (skydoc_17)