Jump to content
IGNORED

New Chrome Pieces I made


Recommended Posts

  • Replies 83
  • Created
  • Last Reply

Top Posters In This Topic

Update

 

Jonas, Hazen, Anyone else that is marked paid below... Thank you!

 

NECK KIT

 

Bongobobny = 1 PAID

Baylensmen = 1 PAID

BIGCAT = 2 PAID

Mcclip = 1 PAID

Slowroll = 1 PAID

Hazenson = 1 PAID

 

CARB EXTENDERS

 

Barrycuda = 1

Balyensmen =1 PAID

Mabelline = 1 PAID

BIGCAT = 1 PAID

Wizzard = 1 PAID

Bongobobny = 1 PAID

Coffskid = 1 PAID

Hazenson = 1 PAID

Friesman = 1 PAID

 

LOCK BEZELS

 

EUSA = 2 PAID

Mabelline = 1 PAID

Baylensmen = 1 PAID

Texlen = 1 PAID

Keith R =1 PAID

BIGCAT = 1 PAID

StarFan = 1 PAID

Wizzard = 1 PAID

Coffskid = 1 PAID

Hazenson = 1 PAID

Friesman = 1 PAID

Tank = 1 PAID

Mcclip = 1 PAID

Gator = 1 PAID

Kantornado = 1 PAID

Rick Hayward = 1 PAID

Gadawg62 =1 PAID

Edited by coop
update
Link to comment
Share on other sites

Ok Gents,

 

The parts will be shipping in a couple days USPS in Priority Flat Boxes. They are all wrapped up and ready to go. I'm just waiting on the amps of primer to arrive. The bezels won't require primer but it would be best to use the primer on the neck and carb kits. It's merely a surface prep so you get good adhesion on vertical surfaces. It comes in a little pen like applicator and is easy to use.

 

The different kits are wrapped in paper please use a scissor to open the packs not a razor knife.

 

The white plastic protective film is still on and looks ugly :o(

If I took it off the pieces would get scuffed during shipping.... the mirrored stainless is not as hard as chrome.

 

Leave the protective film on while installing the pieces so they don't get scratched if you drop one. What I did (included directions that go over this) is peel half of the film back then press it back down, then peel the other half back and press it back down... this way once they are on it'll be easy to get the film off.

 

Careful of the edges.... not the edges but the corners cause they are sharp.

 

Thanks....hope you all like them.

 

Bob

Link to comment
Share on other sites

And the Rear Saddlebag Filler

 

http://i15.photobucket.com/albums/a385/bobn/SaddleBagRearFiller.png

 

very nice! I just saw on my friends Harley where they purposely keep that area open so they have to put more "stuff" in... That piece of yours would look very good there.. You have a gift in fabrication you should explore it as your calling.

:thumbsup2:

Link to comment
Share on other sites

very nice! I just saw on my friends Harley where they purposely keep that area open so they have to put more "stuff" in... That piece of yours would look very good there.. You have a gift in fabrication you should explore it as your calling.

:thumbsup2:

 

Hey hanks Mr. Angel! I appreciate that!

 

Bob

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...